Call us directly 0409 082 026

Restoring the jarrah floors in Nollamara’s older homes

Old jarrah floor sanded back in a Nollamara home

Much of Nollamara was built in the 1950s and 1960s, when jarrah was the everyday flooring timber in Perth homes. Many of those floors are still in place – often under carpet, lino or a thick old coating that has gone orange with age. Floor sanding in Nollamara strips all of that back so the deep red-brown of the jarrah can be seen again.

Older jarrah floors sometimes have shrinkage gaps, a few loose boards or patches where walls were moved during renovations. We secure loose boards, sand the floor flat, edge to the walls and fill gaps before applying the new finish. The aim is a floor that looks original but performs like new.

Once sanded, the floor is polished with several coats of protective finish. Jarrah looks especially good in a satin sheen, which shows off the colour and grain without highlighting every scratch.

Pulled up the carpet in your Nollamara home and found jarrah? Call 0409 082 026 or email bettafloorsanding@gmail.com with a photo.

Floor services for Nollamara homes

Restoration first – plus the trims and new floors that finish a renovation.

Floor sanding

Back to bare timber to remove scratches, stains and worn coatings.

Floor sanding Perth

Floor edging

Detail sanding along walls, corners and doorways the big machine can’t reach.

About edging

Recoating

A light buff and fresh coat for floors that are dull but not damaged.

About recoating

Floor polishing

Satin, semi-gloss or gloss finishes that seal and protect the boards.

About polishing

Splay beading & trims

Neat trims that finish the edges of new or restored floors.

Splay beading

Skirting boards

Skirting boards and quarter rounds fitted to suit your floor.

Skirting boards

Laminate floors

Hard-wearing laminate flooring supplied and installed.

Laminate flooring

Engineered floors

Pre-finished engineered timber floors, laid and ready to use.

Timber flooring

How we bring Nollamara jarrah back

An older floor needs careful preparation before sanding. Here’s how we go about it.

  1. Site check and quote

    We look at the timber type, board condition and any old finish before giving a price.

  2. Clear and protect

    Rooms are cleared, nails set below the surface and doorways protected.

  3. Coarse to fine sanding

    Several passes with finer paper each time take the floor back to clean, flat timber.

  4. Edges, gaps and detail

    Edges and corners are sanded and nail holes and gaps filled to match.

  5. Finish coats

    The chosen finish goes on in coats, with drying time between each one.

Floor sanding for Nollamara’s character homes

Nollamara sits in the City of Stirling between Balcatta and Mirrabooka, with Mirrabooka Avenue and Nollamara Avenue running through it. Its established streets of brick homes on generous blocks have been popular with renovators, and original timber floors are one of their best features.

  • Experience with old jarrah, including shrinkage gaps and loose boards
  • Floors secured and repaired before sanding
  • Satin and matt finishes that suit jarrah’s rich colour
  • Renovation work matched with skirting and trims
  • Free, no-obligation quotes

Restoring original jarrah is almost always cheaper than replacing it, and the colour of old-growth timber is hard to match with new boards.

Satin-finish jarrah boards in Nollamara Gaps filled before polishing, Nollamara Restored post-war timber floor in Nollamara

Floor sanding Nollamara – common questions

Can old jarrah floors with gaps be sanded?

Yes. Small shrinkage gaps are filled after sanding. Wider gaps or very loose boards may need re-fixing first, which we assess when we quote.

Why has my old floor finish turned orange?

Older solvent-based coatings yellow and darken with age and sunlight. Sanding removes the old coating completely, and modern finishes stay much closer to the natural timber colour.

What if walls have been moved and boards are missing?

We can often patch in recycled or matching boards where walls once stood, then sand the whole floor together for an even finish.

Which finish suits jarrah best?

Satin is the most popular choice for jarrah because it shows off the colour without highlighting scratches. Gloss gives more depth; matt gives a natural, low-shine look.

How do I get a quote in Nollamara?

Call 0409 082 026 or send the quote form with the rooms involved and whether the floor is under carpet.

Floor sanding in Nollamara and nearby

We work across Nollamara, from Mirrabooka Avenue to the Balcatta border, and in these nearby suburbs.

See all areas we serve

Bring back the jarrah in your Nollamara home

Free quotes for sanding, polishing and repairs.

0409 082 026

Free quote

Tell us about your floor and we’ll send a free price.

Call now